comp_numeric_transition
Jump to navigation
Jump to search
comp_numeric_transition
is an internal point entity available in Strata Source and TeamSpen's Hammer Addons.
It changes a keyvalue or input over time with various options, when triggered.
KeyValues
- Start Disabled ([todo internal name (i)]) <choices>
-
- 0: No
- 0: Yes
- Entity to Control ([todo internal name (i)]) <targetname>
- The entity to which the outputs will be directed to.
- Keyvalue/Input Name ([todo internal name (i)]) <string>
- The name of the keyvalue or input to change. If the target is not an entity findable by the postcompiler, IO Type must be set.
- I/O Type ([todo internal name (i)]) <choices>
- The method used to control an entity. If Input, use the input name provided. If KeyValue, use the AddOutput to change the keyvalue. If Auto, examine the entity class that is being controlled to determine the appropriate mode.
- auto: Automatic
- io: Input
- kv: KeyValue (AddOutput)
- Value Type ([todo internal name (i)]) <choices>
- The behaviour of the input, used to control what actual values are sent. Regardless of this value, the other options are 'position'-type values!
- set: Instantly Set
- moveto: Move to value
- speed: Adjust Speed
- light: Light Pattern
- Beat Interval ([todo internal name (i)]) <float>
- Time between each output. Smaller values are more accurate but increase the outputs generated.
- Start Delay ([todo internal name (i)]) <float>
- Wait this amount of time after being triggered before animating.
- Duration ([todo internal name (i)]) <float>
- Time the change will take.
- Start Value ([todo internal name (i)]) <float>
- Starting value. If the Value Type is Light Pattern, these may be a-z letters.
- Ending Value ([todo internal name (i)]) <float>
- Ending value. If the Value Type is Light Pattern, these may be a-z letters.
- Easing Start ([todo internal name (i)]) <choices>
- Controls how the animation begins.
- linear: None
- quad: Quadratic (x^2)
- cubic: Cubic (x^3)
- quartic: Quartic (x^4)
- sine: Sinusoidal
- Easing End ([todo internal name (i)]) <choices>
- Controls how the animation ends.
- linear: None
- quad: Quadratic (x^2)
- cubic: Cubic (x^3)
- quartic: Quartic (x^4)
- sine: Sinusoidal
- Name (targetname) <string>
- The name that other entities refer to this entity by, via Inputs/Outputs or other keyvalues (e.g.
parentname
ortarget
).
Also displayed in Hammer's 2D views and Entity Report.See also: Generic Keyvalues, Inputs and Outputs available to all entities
Flags
Only trigger once : [1]
Allow fast retrigger : [2]
Inputs
- Enable
- Allows the relay to fire the OnTrigger outputs after being disabled.
- Disable
- Prevents the relay from firing OnTrigger outputs in response to Trigger inputs.
- Trigger
- Trigger the relay, causing its OnTrigger output to fire if it is enabled.
- Toggle
- Toggle the relay between enabled and disabled.
- CancelPending
- Cancel any events fired by this relay that are currently pending in the I/O event queue.
- EnableRefire !FGD
- Automatically fired on a relay after any delayed outputs finish firing, allowing it to fire again.
- TriggerWithParameter <string> (only in )
- Triggers the relay with a parameter, causing its OnTriggerParameter output to fire if it is enabled.
Outputs
- OnSpawn
- Fired when the relay is spawned. If the relay is set to only trigger once, it will delete itself after firing this output.
- OnTrigger
- Fired when the relay is triggered. If the relay is set to only trigger once, it will delete itself after firing this output.
- OnTriggerParameter <string> (only in )
- Fired when the relay is triggered with a parameter. If the relay is set to only trigger once, it will delete itself after firing this output.