|
|
| (4 intermediate revisions by 3 users not shown) |
| Line 1: |
Line 1: |
| == Making a controllable brush vehicle. ==
| | * [[Half-Life 2 Vehicles]] |
| | * [[Making a controllable brush vehicle]] |
| | * [[func_vehicle]] {{only|{{cs}} {{czero}} {{Sven}} {{jbep3}}}} |
|
| |
|
|
| |
| First make your plane before you do anything. You're going to want to keep it balanced. If it's not it will keep dropping down on the heaviest side.
| |
| SO keep it stays balanced like a real plane would or it will fly funky.
| |
|
| |
|
| |
| Select you whole plane and make it a '''func_physbox''', then give it a name like ''' plane_01'''
| |
|
| |
|
| |
| You need a chair to sit in. You should use the ''' prop_vehicle_prisoner_pod''' (you could use a buggy or airboat but that would look lame) name the chair ''' plane_01_pod''' Also make sure the pod isn't clipping into the planes func_physbox anywhere or it will go crazy sometimes. (it's ok if it clips with a door or other non-phys objects, but not the func_physbox)
| |
|
| |
|
| |
| Next set the outputs to the ''' plane_01_pod''' like so.
| |
| http://www.1337gamer.com/tutorials/vehicle/plane_01_pod_outputs.gif
| |
|
| |
|
| |
| Now make some ''' phys_constrants''' to hold the ''' plane_01_pod''' to the '''plane_01'''.
| |
| http://www.1337gamer.com/tutorials/vehicle/plane_01_pod_constrants.jpg
| |
|
| |
|
| |
| You also might want to make a trigger system to make it easier for the player to get in the plane and one that will
| |
| teleport the player somewhere when exiting the pod so there is no getting stuck.
| |
|
| |
|
| |
| Make a ''' game_ui''' entity. Name it ''' plane_01_game_ui''' Set the outputs for the ''' plane_01_game_ui''' like so.
| |
| http://www.1337gamer.com/tutorials/vehicle/plane_01_game_ui_outputs.gif
| |
|
| |
|
| |
| Not you are going to need 3 ''' logic_compare''' entities. One for each, pitch. yawn. roll. These will control your thrusters.
| |
|
| |
|
| |
| First make a ''' logic_compare''' near the front of the plane and name it '''plane_01_logic_comparey'''. Then set the outputs for
| |
| ''' plane_01_logic_comparey''' like this
| |
| http://www.1337gamer.com/tutorials/vehicle/plane_01_logic_comparey_outputs.gif
| |
|
| |
|
| |
| Make another ''' logic_compare''' on one of the wings. Name it ''' plane_01_logic_comparex''' and set the outputs like so
| |
| http://www.1337gamer.com/tutorials/vehicle/plane_01_logic_comparex_outputs.gif
| |
|
| |
|
| |
| Make another ''' logic_compare''' near the engines. Name it ''' plane_01_logic_fly''' and set the outputs like so
| |
| http://www.1337gamer.com/tutorials/vehicle/plane_01_logic_fly_outputs.gif
| |
|
| |
|
| |
| Now you need to setup the ''' phys_thruster'''
| |
|
| |
|
| |
| Place a ''' phys_thruster''' on the left end on the wing and name it '''plane_01_roll_clockwise'''. Set the parent to
| |
| ''' plane_01''' set the force to 800 and set the direction of the force UP. Go into the flags and check ignore mass.
| |
|
| |
|
| |
| Place a ''' phys_thruster''' on the right end on the other wing and name it '''plane_01_roll_counter_clockwise'''. Set the parent to
| |
| ''' plane_01''' set the force to 800 and set the direction of the force UP. Go into the flags and check ignore mass.
| |
|
| |
|
| |
| Place a ''' phys_thruster''' on the front of the plane and name it '''plane_01_up'''. Set the parent to
| |
| ''' plane_01''' set the force to 800 and set the direction of the force UP. Go into the flags and check ignore mass.
| |
|
| |
|
| |
| Place a ''' phys_thruster''' on the front of the plane and name it '''plane_01_down'''. Set the parent to
| |
| ''' plane_01''' set the force to 800 and set the direction of the force DOWN. Go into the flags and check ignore mass.
| |
|
| |
|
| |
| Place a ''' phys_thruster''' at the end of the left engine and name it '''plane_01_fly1'''. Set the parent to
| |
| ''' plane_01''' set the force to 2000 and set the direction of the force to "14 0 0". Go into the flags and check ignore mass.
| |
|
| |
|
| |
| Place a ''' phys_thruster''' at the end of the right engine and name it '''plane_01_fly2'''. Set the parent to
| |
| ''' plane_01''' set the force to 2000 and set the direction of the force to "14 0 0". Go into the flags and check ignore mass.
| |
|
| |
|
| |
| http://www.1337gamer.com/tutorials/vehicle/plane_01_finished_plane.jpg
| |
|
| |
| -Rickler
| |
| --[[User:Rickler|Rickler]] 17:28, 4 Jan 2005 (EST)
| |
|
| |
| You should now have a basic working plane that will probably need some adjustments here and there.
| |
|
| |
| Example map done by tyrtill it is really crappy and basic but here it is and it works:[http://tyrtill.evosanc.com/shared/sdk_vehicles2.zip sdk_vehicles2.zip] (offline !!!)
| |
| <BR>Edit by Price :
| |
| Here u have convert 2 planes, the fire is only for show its don't hurt
| |
| [http://home.arcor.de/price/bsp/bewegendes.htm plane_examples.zip]
| |
|
| |
|
| [[Category:Level Design]] | | [[Category:Level Design]] |
