Difference between revisions of "Navigation Meshes"
(→Basic Mesh Editing Commands)
(→Editing the Navigation Mesh)
|Line 108:||Line 108:|
# Execute <code>nav_disconnect</code>
# Execute <code>nav_disconnect</code>
Revision as of 05:51, 29 June 2005
- 1 Introduction
- 2 Automatic Navigation Mesh Generation
- 3 Editing the Navigation Mesh
- 3.1 The Navigation Mesh Editor
- 3.2 Using Mesh Editing Commands
- 3.3 Basic Mesh Editing Commands
- 3.4 Advanced Editing Techniques
A Navigation Mesh represents the "walkable areas" of a map. This data is required by Bots and Hostages in Counter-Strike:Source, allowing them to "know" how to move around in the environment.
Navigation Mesh data is stored in a .nav file corresponding to the map file (.bsp) for which it is used. For example, the nav mesh for
cstrike\maps\de_dust.bsp is stored in
To support the many community-created maps, Counter-Strike:Source includes an automatic mesh generation system. The first time you attempt to play a custom map with bots, the generation system will build a .nav file for that map. Depending on the size and complexity of the map, this may take a few minutes to a few hours. Most maps take about 5 minutes to auto-generate a .nav file. Once the generation is complete, a .nav file is saved to your hard drive for future use.
What is Computed During Generation
The following steps occur during Navigation Mesh generation:
- Starting at a player spawn point, walkable space is sampled by "flood-filling" outwards from that spot, searching for adjacent walkable points
- Rectangular Navigation Areas are constructed from the sampled data
- Hiding and Sniper spots are computed
- Encounter Spots and Approach Points are computed (this can take awhile)
- Initial Encounter areas are computed
Manually Starting the Generation Process
To start the generation process manually, type
nav_generate from the console.
To see the resulting Navigation Mesh, type
nav_edit 1. To turn the mesh editor off, type
Explicity Marking Walkable Areas (ie: "There's no mesh upstairs")
Some maps that have very steep stairs, ramps, or hills may confuse the generation system, resulting in the Navigation Mesh not covering the entire map. To solve this, you can manually place additional walkable markers that tell the generator to search outwards from that point during its sampling phase.
To add one or more walkable markers, first aim your view towards a known walkable spot in your map, then type
nav_mark_walkable in the console. When you are finished placing markers, type
nav_generate to re-generate the mesh.
Quickly Generating Meshes for Testing
The analysis phase of the generator can be quite time consuming. To skip it, type
nav_quicksave 1 in the console.
NOTE: "Quicksaving" skips the analysis phase, and the resultant nav mesh will be missing important data required by the CS Bots and Hostages higher-level planning and attention systems. While useful for testing, editing, and tuning a nav mesh, be sure to do a full analyze (ie: with
nav_quicksave 0) before publishing your nav file to others.
The automated Navigation Mesh generator does a reasonable job of constructing a mesh, allowing you to start using Bots and Hostages on custom maps easily.
However, careful hand-tuning of the Navigation Mesh can markedly improve the performance of Bots. In addition, manually decorating the mesh with Place Names allows the Bots to tell others where events occur, enhances the Counter-Strike radar and includes Place Names in all radio messages.
To enable the editor, type
nav_edit 1 in the console (type
nav_edit 0 to disable it).
- The white cross in the center of your view is the cursor.
- The Navigation Area you are pointing at is the selected area and is shown with a yellow outline.
- Navigation Areas that can be reached from the selected area are shown in red.
- The white line in the selected area denotes where the area will be split if the
nav_splitcommand is executed.
Using Mesh Editing Commands
Although all of the mesh editing commands can be typed in the console, in practise it is far easier to bind these commands to keys. For example,
bind del nav_delete binds the delete key to the command nav_delete. After this binding, pressing the delete key will delete the nav area under your cursor (if you are nav editing mode).
Basic Mesh Editing Commands
To merge two adjacent areas:
- Aim your cursor at the first area and execute
- Aim your cursor at the second area and execute
Note that both areas must be the same size along the edge to be merged.
The resulting area will retain all of the connections of the original two areas, and inherit properties (ie: Place Names, etc) from the marked area.
Splicing creates a new area between two existing areas.
To delete an area, aim your cursor at it and execute
Creating a New Area
To manually create a new area:
- Place your cursor at where a corner of the new area should be
- Move your cursor to drag out the area's extent
Adding and Removing Connections Between Areas
The connections between areas define whether an agent can move from one area to another. Usually these connections are bidirectional, meaning agents can move back and forth between two areas at will. However, sometimes the connection is one way, as in the case of high ledges that can be jumped down, but not back up.
To make a one-way connection from area A to area B (meaning you can move from A to B):
- Place your cursor on area A
- Mark area A with
- Aim your cursor at area B
To make a bidirectional connection, repeat the above steps reversing the roles of A and B.
To remove all connections from areas A and B:
- Aim at area A
- Mark area A with
- Aim at area B
Advanced Editing Techniques
Preventing Excessive Jumping
When to use the
Obstacle Avoidance and Precision Movement
nav_precise flag to disable local obstacle avoidance behaviors.
Marking Areas to Avoid
nav_avoid to tell bots to avoid the area unless the normal route has become too dangerous.
Controlling Where Bots Can Hide
nav_no_hide to prevent bots from hiding in that area.
How to force the creation of hiding spots during the analysis phase.
Addition information can be found here.